Buy 11RB24 Resolver Electrical part by Ducommun Labarge Technologies Inc

Part Number: 11RB24

Manufacturer: ducommun labarge technologies inc

NSN: 5990-01-025-7465

NIIN: 010257465

Item Name : resolver electrical

CAGE Code: 08719

FSC: 5990 Synchros and Resolvers

INC Code: 22966

Country: USA

NCB Code: 01

FSG: 59 Electrical and Electronic Equipment Components

We've received your request for 11RB24 (described as Resolver Electrical), manufactured by Ducommun Labarge Technologies Inc with CAGE code 08719. This part is registered under NSN 5990-01-025-7465, classified in FSG 59 Electrical and Electronic Equipment Components / FSC 5990 Synchros and Resolvers. Our verification process will confirm traceability through supporting identifiers including NIIN 01-025-7465, NCB code 01 (origin: USA), and INC 22966. Please submit your formal quotation request to proceed.

Thank you for choosing Aerospace Exchange for your 11RB24 requirements. We specialize in authenticated aerospace components, offering both NSN-tracked military parts and commercial equivalents, all validated through our rigorous sourcing protocols.

Note : We Will Not Share Your Information To Any Third Parties.

Please fill out below form for 11RB24

Contact Information

“*” Required Fields Are Compulsory

* By clicking this box, I acknowledge that I have read and accept the ASAP Semiconductor Terms and Conditions and agree that all quotes and purchase orders are exclusively subject to the ASAP Semiconductor Terms and Conditions.

I consent to receive email communications from ASAP Semiconductor and can unsubscribe at any time.
ASAP Semiconductor is a wholly independent aftermarket parts distributor.
This website is intended for quotations based on part numbers only. Please DO NOT submit drawings, technical data, or other specifications through this portal.

Disclaimer: This is a quotation for the goods listed above. This quotation is meant as an estimate and does not reflect a final bill or invoice. All quotations are subject to change until acceptance by ASAP Semiconductor of a binding Purchase Order, and quotations may be withdrawn or revised at the sole discretion of ASAP Semiconductor. This quotation is subject to the ASAP Semiconductor Terms & Conditions available at https://www.asapsemi.com/terms-conditions.aspx . All United States Government and Department of Defense bids are quoted as CAGE code 6RE77 from ASAP Semiconductor’s Anaheim, California facility. Any quotation from ASAP Semiconductor without 6RE77 is void.

If You Have Multiple Parts Requirement,
You Can Upload Your Parts List or BOM Here!

Upload

How to Begin the Quotation Process

Fill out and submit the form for part 11RB24, on this page with details like your required quality and target pricing included.
Our staff will receive and review your information, quickly formulating fitting solutions based on your specifications.
Within 15 minutes or less, an account manager will contact you to present options and discuss how you can proceed with procurement.

NSN Information for Part Number 11RB24 with NSN 5990-01-025-7465, 5990010257465

NSN	FSC	NIIN	CLS	Hazmat	DEMIL	Cancelled NSN
5990-01-025-7465 Item PartTypeName: RESOLVER,ELECTRICAL	5990	010257465	0	N
	CIIC	HCC	ESD	PMIC	Criticality	ENAC
	U			U
Part Number	ISC	RNVC	RNCC	HCC	MSDS	SADC
11RB24	5	9	5

Characteristics Data of NSN 5990-01-025-7465, 5990010257465

MRC	Criteria	Characteristic
AAFZ	BODY MATERIAL	STEEL,CORROSION RESISTING
AAQL	BODY STYLE	STANDARD ROUND,ROTATABLE STATOR B
AAVH	SHOULDER DIAMETER	0.9995 INCHES MINIMUM AND 1.0000 INCHES MAXIMUM
AAVL	PILOT DIAMETER	0.6245 INCHES MINIMUM AND 0.6250 INCHES MAXIMUM
ABHP	OVERALL LENGTH	3.3170 INCHES MAXIMUM
ABKK	FLANGE DIAMETER	1.0600 INCHES MINIMUM AND 1.0620 INCHES MAXIMUM
ABKU	FLANGE THICKNESS	0.0900 INCHES MINIMUM AND 0.0960 INCHES MAXIMUM
ABPA	UNDERCUT DIAMETER	0.9750 INCHES MAXIMUM
ABPC	UNDERCUT WIDTH	0.0450 INCHES MINIMUM AND 0.0550 INCHES MAXIMUM
ABPM	BODY DIAMETER	1.0590 INCHES MINIMUM AND 1.0670 INCHES MAXIMUM
ABWV	SHAFT DIAMETER	0.1195 INCHES MINIMUM AND 0.1200 INCHES MAXIMUM SINGLE SHAFT
ABXF	SHAFT LENGTH	0.4290 INCHES MINIMUM AND 0.4510 INCHES MAXIMUM SINGLE SHAFT
AEBZ	SCHEMATIC DIAGRAM DESIGNATOR	2 ROTOR,2 STATOR,2 COMPENSATOR,2 RESISTOR
AFJN	FRAGILITY FACTOR	MODERATELY RUGGED
AHCG	MAXIMUM TEMP RISE	10.0 DEG CELSIUS
AJSL	BODY SIZE	11
AJSR	ROTOR INPUT VOLTAGE RATING IN VOLTS	15.0 NOMINAL
AJSS	FREQUENCY IN HERTZ	400.0 NOMINAL
AJTG	ZRO IMPEDANCE MAGNITUDE IN OHMS	500000.00 MINIMUM
AJTJ	ZSO IMPEDANCE MAGNITUDE IN OHMS	500.00 MAXIMUM
AJTK	ZSO IMPEDANCE ANGLE IN DEG	35.00 NOMINAL
AJTW	TRANSFORMATION RATIO EQUALITY IN PERCENT	0.1 MAXIMUM
AJTX	COMPENSATION METHOD	WINDING COMPENSATED
AJVF	PHASE SHIFT ANGLE IN DEG	0.100 INPUT TO OUTPUT MAXIMUM
AJVG	MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT	20.00 INPUT
AJVH	MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT	25.00
AJVJ	INTERAXIS ERROR ANGULAR RANGE IN MINUTES	-3.0 TO 3.0
AJVK	OUTPUT VOLTAGE FUNCTIONAL ERROR RANGE IN PERCENT	-0.1 TO 0.1
AJVL	ELECTRICAL ERROR ANGULAR RANGE IN MINUTES	-3.0 TO 3.0
AJVS	ACTUATOR FRICTION TORQUE AT MINUS 55 DEG CELSIUS	30.0 CENTIMETER-GRAMS MAXIMUM
AJVT	ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS	15.0 CENTIMETER-GRAMS MAXIMUM
AJVW	ALIGNMENT HOLE QUANTITY	4
AJWE	SHAFT RADIAL PLAY TEST POINT	0.250 INCHES NOMINAL
AJWG	SHAFT MAXIMUM RADIAL PLAY	0.0008 INCHES
AJWH	SHAFT END PLAY	0.0005 INCHES MINIMUM AND 0.0015 INCHES MAXIMUM
AJWP	TERMINAL DESIGNATOR AND SCHEMATIC POSITION	CONNECTION R1 POSITION H AND CONNECTION R2 POSITION G AND CONNECTION R3 POSITION E AND CONNECTION R4 POSITION J AND CONNECTION S1 POSITION L AND CONNECTION S2 POSITION L AND CONNECTION S3 POSITION K AND CONNECTION S4 POSITION N AND CONNECTI
AJWQ	PILOT LENGTH	0.0590 INCHES MINIMUM AND 0.0650 INCHES MAXIMUM
AJWR	SHOULDER LENGTH	0.0590 INCHES MINIMUM AND 0.0650 INCHES MAXIMUM
AJWX	MOUNTING SURFACE TO TERMINAL END DISTANCE	2.9660 INCHES MAXIMUM
AJXB	SHAFT MAXIMUM RUNOUT	0.0010 INCHES
CQTM	TERMINAL LOCATION	SIDE
CRSJ	SHAFT TYPE	ROUND SINGLE SHAFT
CRSY	ALIGNMENT HOLE DEPTH	0.1250 INCHES MINIMUM
CSJY	TRANSFORMATION RATIO	1.000 ROTOR TO STATOR NOMINAL
CTCW	ALIGNMENT HOLE BOLT CIRCLE DIAMETER	0.8120 INCHES NOMINAL
CWXK	SHAFT RADIAL PLAY DETERMINING WEIGHT	4.0 OUNCES
CWYF	SHAFT END PLAY DETERMINING WEIGHT	8.0 OUNCES
FEAT	SPECIAL FEATURES	SPUR GEAR
TTQY	TERMINAL TYPE AND QUANTITY	12 WIRE LEAD

Schedule B & Trade

End Use : 21610	Medicinal equipment
Schedule B : 9018903000 (NAICS 339112)	Anesthetic instruments and appliances and parts and accessories
SITC : 87229	Instruments and appliances used in medical, surgical or veterinary sciences, n.E.S.

Identification

CRITL	The item does not have a nuclear hardened feature or any other critical feature such as tolerance, fit restriction or application.
HMIC	N - Indicates there is no data in the hmirs and the nsn is in a fsc not generally suspected of containing hazardous materials.
PMIC	U - Precious metal content is unknown

NSN Management Codes

AAC	J
Classification Control	U
MGMT_CTL	9b-----
Quantity per pack	1
Repariability
Shelf Life	N/A
SOS	Sms
Unit of Measure	Ea

Freight Information

ACC:	V - Trailers, vehicles, machinery, shop and warehouse equipment and supplies including special tools and equipment, ground servicing
ADC:	A - Shipment is not a consolidation and does not exceed 84 inches in any dimension.
LTL:	W - Rating variable
NMFC:	062120 - Generators/motors/parts noi
SHC:	9 - Other or no special handling required (sh)
TCC:	Z - No special type of cargo code applicable
WCC:	593 - Motors and parts, (machinery and parts),(less than 35 feet)